[dk999]

To jump into the topic:
I’ve set my pi to HDMI group 1 and mode to 4 (720p). I want all my Emulators to stretch the image to 16:9 and have set the configfiles Tod:
Custom_vieport_width = 480
Custom_viewport_height = 640
Aspect Ratio to 1.33 and screen to 16:9 but only some like pocketsnes work and Emulators like picodrive give me fullscreen with master system games but a cropped and smaller image with borders in mega CD games. Where’s the problem? -_-

[dk999]

So here’s my Config as .txt :)

EDIT: Found it, was the phosphor shader which was in my retroarch.cfg for all emulators, didn’t overwrite the value in my specific SNES retroarch.cfg though

[dk999]

Can’t load any shader via retroarch, doesn’t seem to take any effect even by setting them manually through retroarch.cfg :-/

Hardware is Pi2 with Beta 2.5

[dk999]

[quote=86854]
Well until everything gets sorted out on the rpi2 maybe. Buts there is no reason to keep your b+ or to support it long term. Just buy the new raspberry 2 Its $35. That’s 10 or so coffees, 3 meals at macers
[/quote]
Was just wondering if there will be two images for the next versions as long as many people claim for it. I’ve ordered my Pi2 yesterday but a statement from the developer(s) would be nice. Do I have to compile everything on my own for maximum speed on my Pi2? Will there be only a Pi1 version because it also runs on the Pi2?

[dk999]

With RPi2 using ARMv7, will there be two RetroPie-Distributions in the long run, compiled for each architecture?

[dk999]

Got normal Heatsinks, temp never rises above 55°C :)

################ HDMI ######################
hdmi_group=1
hdmi_mode=16
disable_overscan=0
overscan_scale=1
overscan=1
#hdmi_force_edid_audio=1
#config_hdmi_boost=4

################# CLOCKS ####################
arm_freq=1100
#arm_freq_min=600
core_freq=550
sdram_freq=600
v3d_freq=550

################# VOLTS  #####################
over_voltage=6
over_voltage_sdram=1

################ MISC #######################
avoid_safe_mode=1
gpu_mem=256
force_turbo=0
#avoid_warnings=1
avoid_pwm_pll=1
dwc_otg.speed=1

[dk999]

Hi Guys!
Tried to use CMA on my Pi with Firmware 3.12.35+, though I only get a “lwl0: error creating SDL Window” and be greeted by the terminal instead of Emulationstation.

I’ve got the 512 B+ Model and the following cmdline.txt

dwc_otg.lpm_enable=0 console=ttyAMA0,115200 kgdboc=ttyAMA0,115200 console=tty1 root=/dev/mmcblk0p2 rootfstype=ext4 elevator=deadline rootwait coherent_pool=6M smsc95xx.turbo_mode=N

and config.txt

disable_overscan=0
overscan_scale=1

overscan_left=16
overscan_right=16
overscan_top=16
overscan_bottom=16

hdmi_group=1
hdmi_mode=16

arm_freq=1000
core_freq=500
sdram_freq=500
over_voltage=6
over_voltage_sdram=4
avoid_safe_mode=1
gpu_mem=256
gpu_mem_256=160
gpu_mem_512=416
cma_lwm=16
cma_hwm=32
force_turbo=0
overscan=1

It doesn’t work, no matter what I’m doing with the gpu_mem_512 line. It’s like emulationstation doesn’t like the cma-commands at all.
By the way, when using i.e. 384MB for the gpu as a fixed value ( no CMA ), I only get a blank white screen for emulationstation.

Any suggestions?

[Author]

Posts